| View previous topic :: View next topic | 
	
	
		| Author | Message | 
	
		| pinotgraves 
 
 
 Joined: 11 Jun 2009
 Posts: 5
 Location: California
 
 | 
			
				|  Posted: Mon Nov 08, 2010 8:54 pm    Post subject: Which cam? |   |  
				| 
 |  
				| I have acquired a late Crown Graphic with a top-mounted rangefinder--but no lens or lensboard. How do I determine which which lens (and thereforefore which cam) it is set up for/with? Also, for extra credit, what battery model fits it little built-in focuspot lamp? Thanks--I couldn't find a thread on the forum with the answer....
 _________________
 Stop me before I gear up again!
 |  | 
	
		| Back to top |  | 
	
		|  | 
	
		| 1banjo 
 
 
 Joined: 16 Nov 2008
 Posts: 492
 Location: kansas
 
 |  | 
	
		| Back to top |  | 
	
		|  | 
	
		| 45PSS 
 
 
 Joined: 28 Sep 2001
 Posts: 4081
 Location: Mid Peninsula, Ca.
 
 | 
			
				|  Posted: Tue Nov 09, 2010 2:43 am    Post subject: |   |  
				| 
 |  
				| Lens were optically measured and a cam was cut to match the actual focal of the lens.  Actual focal length of a given lens may be ± 5% of the stated focal length. 
 With the cam and lens installed on the camera focus the lens on an infinity target at least 5000 feet away, then check the rangefinder for coincidence.  Infinity position of the rails is fully in then out .040 inch ± .010 inch.  With rails locked in this position the RF should be in coincidence with any cam installed.  If the lens is not at infinity focus, loosen the infinity stops set screws and move the lens to where the infinity target is in sharp focus with the front standard locked and both sides equal distance from the rail ends.  Slide the infinity stops up to touching the front standard and tighten the exposed set screws.  Unlock the front standard, move it back and tighten the back set screws.  Over tightening the set screws will damage the rails.  Front set screw should have a flat bottom, rear set screw should have a sharp point.
 
 With a matched lens/cam both will be in focus thorough the entire focal range, a close match will be off more at close distances than at far distances.  All test should be done with the lens wide open.
 _________________
 The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
 |  | 
	
		| Back to top |  | 
	
		|  | 
	
		| bartbob 
 
 
 Joined: 30 Oct 2010
 Posts: 102
 
 
 | 
			
				|  Posted: Fri Nov 12, 2010 12:33 pm    Post subject: Rangefinder Cam Number vs. Lens Focal Length |   |  
				| 
 |  
				| Regarding the info shown in: http://graflex.org/speed-graphic/top-rangefinder-cams.html , I see the following data for cams P32 through P38:
 
 32 138.7
 33 140.4
 35 144
 38 148.9
 
 My SSG's lens board has "CAM 36005 P34" stamped on it.  Does this mean its Optar/Rodenstock "135mm" lens' focal length is really between 140.4 and 144 mm?  There's no P number "34" in that list.
 
 Still learning........
 
 Thanks,
 
 Bart
 
 Last edited by bartbob on Mon Nov 15, 2010 3:53 am; edited 1 time in total
 |  | 
	
		| Back to top |  | 
	
		|  | 
	
		| 45PSS 
 
 
 Joined: 28 Sep 2001
 Posts: 4081
 Location: Mid Peninsula, Ca.
 
 | 
			
				|  Posted: Fri Nov 12, 2010 9:16 pm    Post subject: |   |  
				| 
 |  
				| The cam information for the Top Rangefinder Pacemaker does not apply to the Super Graphics. The cam list for the Supers is:
 http://graflex.org/speed-graphic/super-graphic-cams.html .  (Be sure to leave a space after a pasted link as the system will include any character up to the next space as part of the link making the link bad.)
 
 The P34 cam is machined for a lens having a focal length of approximately 136.4mm.
 _________________
 The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
 |  | 
	
		| Back to top |  | 
	
		|  | 
	
		| bartbob 
 
 
 Joined: 30 Oct 2010
 Posts: 102
 
 
 | 
			
				|  Posted: Mon Nov 15, 2010 3:56 am    Post subject: |   |  
				| 
 |  
				| 45PSS, thanks for noting my link to the wrong camera....and that the link included a character that must not be part of it.  I'll save the correct link in my Graflex files. 
 Bart
 |  | 
	
		| Back to top |  | 
	
		|  | 
	
		|  |