Graflex.org Forum Index Graflex.org
Get help with your Graflex questions here
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Lens Removal

 
Post new topic   Reply to topic    Graflex.org Forum Index -> Speed Graphic Help
View previous topic :: View next topic  
Author Message
gregr



Joined: 25 Mar 2023
Posts: 4
Location: Oregon

PostPosted: Sun Mar 26, 2023 1:13 am    Post subject: Lens Removal Reply with quote

I recently acquired an Anniversary 4X5. This is my first with a wood lens board. I want to ship the lens off to a repair facility. It is a No 2 Supermatic shutter with a three screw retaining flange. For the life of me I can not get the flange to budge to unscrew it. I've tried a friction method with a rubber stopper, then a punch on one of the screw holes. From the looks of it, it was punched before, but very lightly. Would lighter fluid seeped in behind the flange help? The camera and board are still pristine, so I'm being careful about marking it up. Maybe too careful? Thank you!
Back to top
View user's profile Send private message
Dan Fromm



Joined: 14 May 2001
Posts: 2133
Location: New Jersey

PostPosted: Sun Mar 26, 2023 12:47 pm    Post subject: Reply with quote

The shutter should unscrew from the flange. Unscrew the lens cells from the shutter and then try to remove the shutter from the flange.

If you can't get the things apart, send board and all to the repairman.
Back to top
View user's profile Send private message
JESimmons



Joined: 03 Dec 2012
Posts: 26
Location: St. Simons Island, GA

PostPosted: Mon Mar 27, 2023 11:39 am    Post subject: Reply with quote

After removing the lens elements, you might try spraying the shutter to flange threads with electrical contact cleaner. That may clean them out without leaving residue. I get my cleaner from Ace Hardware in the US.
Back to top
View user's profile Send private message
gregr



Joined: 25 Mar 2023
Posts: 4
Location: Oregon

PostPosted: Mon Mar 27, 2023 6:45 pm    Post subject: Reply with quote

Thank you for the replies. While searching for the lens wrench I put a dab of Kroil on the rear threads off of a screw driver blade after removing the rear element. I'm going to give it some time to soak. The repair shop is Advance Camera in Portland Oregon. I've used them many years ago and recognized the Graflex lens I took in at the time and it was like yep we seen them. When I called this time they had to look it up. Personnel change? If it does come to shipping with the board I'll verify 1st.

I don't want to unscrew the shutter body. There may be an indexing pin as this one has a solenoid trip mounted on the board.
Back to top
View user's profile Send private message
gregr



Joined: 25 Mar 2023
Posts: 4
Location: Oregon

PostPosted: Fri Mar 31, 2023 4:04 am    Post subject: Reply with quote

Success, sort of. The lens was "GLUED" to the board. There has a hole for an indexing pin in the board, but none on the lens so it was literally glued to the board with some sort of clear cement that also got in the threads. I got a heavier duty lens wrench just in case and it was the needed tool. So now it's off to the shop for CLA.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Graflex.org Forum Index -> Speed Graphic Help All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group